Search results

I ended up buying the Tyga rearsets. These are for my wife's RC390 so I do not really expect her to destroy the heel guards. I decided to read up a little I have friend coming over Sunday to help me install these. The brake stop is no longer an item of concern? I just wanted to see if there was...

My wife's rc was doing this and she was having hunting for neutral issues. I adjusted the shift rod and her shifting issues never returned. I think I read it on this forum. While you are down there tighten your kickstand bolts they will eventually back out. I took the forum advice and put blue...

Has anyone installed these yet? I have learned from stupid mistakes in the past and decided to read the directions to see if a full engine oil drain is needed. The instructions say some engine oil may escape. I wanted to know if these should wait for install during an oil change (which is far...

Filter MWR Performance & Race Filter For KTM 125/200/250/390 Duke (2014-15) & | Bellissimoto $76.95 Power up kit MWR Power Up Kit For KTM RC 390 (2015+) | Bellissimoto $64.95 thats pricey!

very cool I have the MWR Race filter on my R1. We already have the K&N setup on the RC390 otherwise I would go this route.

Reviving this thread because I remember seeing these and saw pics of an engine case ground down. These would have saved it. Ordered!

This thread saved me $30! My wife bent up the lever and I surprised it was only $8 on bike bandit to replace. But I couldn't figure out how to get the clutch lever off and decided to do a search on the forum.

How much extra was the ceramic coating? Our Werkes badge had a bad batch of paint and it all faded. Werkes offered to fix it no charge I asked if we could wait until end of season and they said yes. Maybe I'll have it coated while they have it for the repair.

Did this die off due to the PCV quickshifter? The wife wants a quickshifter and we run the powertronic unit on the bike. I do not want to invest into the PCV setup. Does this setup work ok for GP Shift? I am interested in the long term reliability of this unit and if anyone is still using it. Do...

The front stands from cycle gear use flat pads to push up the forks. Pitbull stands have 2 padded pins that hold the forks pretty snug. Never had a problem again with that pit area.

I have the Pitbull removable handle ones and have fitted the head lift stand also using the pin from pit bulls website. No issues with either fit. The cheap stands are good until they are not good... I had my track bike (ZX6R) fall off cycle gear brand stands at NYST. The pit area there is on a...

Congrats welcome to the addiction. I am assuming you ride with TPM? My wife and I ride with TPM you will see her on her RC390 at track days. We are done for the season up here. We end the track season early and finish around September due to work. Check your tire pressures. We run Rossi 2 tires...

Just to add, the customer service is top notch. When I ordered the ones in the picture, Tech Spec did not have any vendors selling these. They cut them and shipped them right out. With a quick verification, they also offer a military discount. I use Tech Spec on all of our bikes including my...

Try tightening the shift rod. Our RC390 was having problems with neutral and 1st first gear until I tightened the shift rod.

I am following this thread because I just ordered up a whole brake upgrade for the RC390 and the next project is rearsets. I am really leaning towards the Driven TT since this appears to remain a constant issue for Tyga. Is Tyga replacing the broken heel guards or is everyone forking out $21...

Here is the Tech Spec we have. I had to order direct from Tech Spec. They have been on since October 2015 with no problems.

Do you have a link for where you purchased? Looking to do this for the RC390 and I am also looking at upgrading the master cylinder.

I ended up buying a Powertronic from a forum member and it has been working flawless. My wifes RC has the Werkes exhaust, K&N Filter mod. We have been running Map 1 for about 8 months or so. Last week I threw on map 4 and she says its a whole new bike. Her acceleration is a very noticeable...

Well, just did a full oil and filters change on the RC390 and the Oil Screen Screw plug M17x1.5 has a torque of 8.9lbft did not make it to 8.9 before it snapped off. Thank God there was enough left to use pliers and twist it back out of the engine. I reused the old one. From now on no torqueing...

We are in search of new lighter wheels for the RC390. It does not look like there are any options. The Gale speed require modifications for the sprocket and cush? I decided to do some forum searching this morning. These stock wheels are ridiculously heavy. I wanted to revive this thread for some...