Hey, thinking about putting a slightly smaller rear sprocket on at one time. I know Formula390 knows this stuff inside and out.
Iknow there will be slightly less acceleration, slightly greater fuel economy, and slightly less revs at the same speed.
What are the quantitative measurements on...
From the ninja 400 forums, user C Dolan:
The vibration issue and the more upright riding position would have
me favor the Kaw, especially if I was riding more than 100 miles nonstop.
Both handle well, but the KTM rear rim is way too narrow for its
150 rear tire. Slid the ass end a lot...
So I was cleaning my chain today and ask went well until at the end when I decided to turn my bike on while it was on the rear stand. I had it in first gear with the clutch pulled all the way, and then I notice the rear wheel is spinning. I adjust my lever all the way out so I'm pulling the...
Just got my hands on a 2015 with 1900miles. Will be tracking this bike so every stock part must go.
Seats
Signals-TWO SETS OF REAR SIGNALS WITH TIDY TAILA
mirrors-SOLD
lower fairing-SOLD
all the rearsets-ONE SET OF PASSENGER, HAVE THE RIGHT SIDE LEFT
kickstand-ONE LEFT
stock windscreen...
I have for sale my 2015 KTM RC390. Purchased it brand new. Bike is in great condition, clean title and never been tracked. The bike has been sitting in my living room. Has 6154 miles on it. I'v done a ton of work on the bike, see below.
Ohlins KT303 Rear shock
Andreani Fork Cartridge Kit
Werkes...
415 Front Sprockets are rolling off the machining center constantly now. Stock for the rear sprockets should be here later this week and will have an array of offerings for rear sprocket sizes. Sprocket fitment is perfect! These front sprockets are made from hardened Chromoly 4140, and have cold...
This is my first post I suppose, so hello. I live outside St. Louis, Missouri. I thought for sure I had an account when I first bought the bike a few years ago, but couldn't seem to figure out my info.
Anyways, I need to replace my front and rear brake pads. The bike is not currently with me...
Well slowly but surely this bike is getting ready for next season.
The Tyga bodywork is on, power commander and quick shifter installed, all the street stuff removed and sensors have resistors to avoid check engine lights, oil changed, coolant flushed, valves adjusted and all that little BS...
SOLD
List of upgrades:
Powercommander V
Ohlins KT303 rear shock
Racetech Springs and adjustable ride height in front forks
Full SAMCO radiator hoses with Engine ice
Galfer wave rotors and pads front and back
Rear black Marchesini Wheel
Spal 5.2 puller fan
Dual White LED headlights with...
272.7 lbs with 2/3 of a tank of gas -at least that is what the math said after I subtracted the weight of the board the bike was sitting on.
I’m not bragging and my goal was not go to great lengths to try to lighten the bike. This was merely a labor of love of tinkering and aesthetics. This is...
Hey All,
I have a barely used JRi Rear Shock for a 2015 KTM RC 390 that I'm looking to sell.
It has just under 2k miles on it.
It is sprung and tuned for 150 pounds.
I'm looking to get $400 obo.
Anyone having any issues with the front of the bike outweighing the rear so much? right now i have 170 front to 150 rear. the 20lb different seems a lot to me. the back end does bounce around a LOT. Just curious what everyone else is at? any recommendations? etc! Note required to be at 320lbs...
So I went all in and built a hyper 390... started with a brand new 2017 390..
at over 20,000 its probably the most modded 390 out there
PCV, Wideband O2 w/ Autotuner and quick shifter
Andreani fork kit and Ohlins KT303 46HRCL rear
Driven Triple Clamp and Clipons
Hot Body race body and Tyga...
Thought I would document my build for this season racing 400 Production Cup here in Colorado, and a couple of rounds in Utah.
Background, I raced a Yamaha R3 last year and sold it at the end of last season. I bought a Honda RS125 GP two stroke to race but realized that there wasn’t much of a...
Love My RC. Nothing wrong at all. Just stumbled upon the competition...
Article from the motorcyclist::
What does $5,299 buy you in 2018?
Let's start here:
Kawasaki's Ninja 400 ABS, a sport motorcycle made in Japan. Basic specs include a 399cc engine (from a 70mm bore and a 51.8mm stroke)...
Hi,
I'm looking for after market rear sets, one of the known brands, woodcraft, tyga, hot bodies, something like that.
Anyone have a set for sale at a reasonable price?
Thanks,
Mike